We allow links, pictures, video, or audio file to help diagnose your problem. The result: The compression that's supposed to be at 160 is at less than 60. Place the pump aside with the lines attached. If they all say it's the actuators, it probably is. If necessary, tap with a rubber mallet to loosen the cover.
Those who demonstrate they cannot follow the rules will be warned and posts removed. Even with cruise control, the car's power decreases. Also due to the check engine light the remote start isn't working either. I found the manual online and printed out the pages about P0008. The technician diagnosed that the evap purge valve was defective. My vehicle has 116xxx miles.
We are more than happy to help you figure out why a shop wants to charge you for a repair, and we will tell you if it is unusually high. Have to manually unlock by hand from the inside. Contributing posters are people who regularly post worthwhile advice. As the bolt unscrews it's going to push the power tool against that componant and possible bust it. The contact stated that the engine warning indicator illuminated. Remove the fan and radiator.
I am petrified to pull out in traffic with this car. Melling timing chains are manufactured using the highest quality designs, materials and workmanship. Take care and best of luck. This will allow people to filter out posts that have already been resolved so they can move on to other posts that still need assistance. Personally, I'd go get a second and third opinion.
A few minutes later the car started to tug, and pull back and just created resistance against me when I wanted to give it gas. Could it be that it was just barely off so it took awhile for the computer to notice? Sharing personal information, or specifics on is not allowed. The dealer Suzuki depot, 936 E 3rd St, santa ana, ca 92701, 800 338-9208 was contacted. Before an accident or loss of life happens. The approximate failure mileage was 170,000. This involves removing the intake manifold so the valve covers can come off. All posts without this information may be subject to being removed.
The power steering pump and mount, And finally Crankshaft pulley. I would strongly recommend having the dealer do this repair. There are three timing chain tensioners on this engine, and causing this problem is the number 1 timing chain tensioner that is not properly adjusted. The vehicle was taken back to the dealer who stated that the front wheel bearing needed to be replaced. The manufacturer was not notified of the failure.
Long story short, I had a recurrent P0009 code. Does it surprise you that it drove fine for 6 days before the code set? Replacement brand parts are the most affordable solution for all of your replacement needs! The flat rate on this job is 8. By having another shop inspect and diagnose the problem without telling them what the original shop said, I should have an unbiased idea of what's really going on. One of the tensioner tracks had disintegrated into about a dozen bits. In addition, the contact stated that while driving at 55 mph, the vehicle would shake and had a loud noise coming from the front wheels. Either condition would cause the camshaft timing for both cams on one bank to be off an equal number of degrees. The water pump has 4 screws, Just make sure you cover up the oil pan so the antifreeze does not go in there.
After a stop light, I headed up a hill and the car just fought me down to a dead stop. A tip to remove the big nut on the crankshaft is as follows. This is a 3 day repair job at minimum. If we feel a piece of advice is particularly reckless, dangerous, or extremely unhelpful it maybe removed If a post or comment is provided that is not a response to a question, the post may be removed. The vehicle was taken to the dealer. When you get the cover off, check how far the tensioner has extended, if it's more then about 4-6 clicks, the chain is stretched and should be replaced.
Tighten the bolts to 11 Nm 97 in. While you are in there, you can inspect the timing chains, it has 3. I was told that this expense is my cost even though I only had the vehicle 9 days. Now it sets within just a couple miles of driving. The misalignment would be at an idler sprocket for either bank or at the crankshaft. In July 2005, I decided to investigate this noise. How is this legal Suzuki? Fortunately, he admitted that there was enough of a doubt to open it back up without charging me.
The water pump is mounted behind it. That the car was sold as is. The engine is an interference fit, so being 1 tooth off on the timing can will bend valves. Please report bad advice to the mod team. In my experience, if the tensioner is gone, then the chain, sprockets and guides will also be worn and should be replaced as an assembly.