Figure 9 Thermostat - The thermostat has three lines connected to it, a hard metal line that is connected via a 10mm bolt and a gasket green arrow , a quick disconnect to the lower radiator hose red arrow and the upper coolant hose connected via a hose clamp. The temperature of the outlet air should be 35. On the lower left side of the radiator is a drain valve as well as the coolant temperature sensor. Apr b8 30 tfsi supercharger coolant performance system cps. Select Your 2017 Audi A4 There are three ways to find the exact Audi A4 parts you're looking for on eEuroparts.
Please make sure someone will be available at shipping address to sign for package. A few things to note about coolant is that it is sweet tasting and highly toxic, so it can end up in the dog's stomach pretty quickly. Figure 1 On the lower left side of the radiator is a drain spigot red arrow. Do not lubricate guide sleeve for release bearing. Reversing the direction in which it runs can ruin it.
Figure 3 Upper Hose - One of the weakest spots in the cooling system is where the coolant overflow hose yellow arrow meets the upper quick disconnect red arrow. Apr 3040 tfsi coolant performance system cps chart chart. By entering this site, you agree to hold Pelican Parts free from any liability arising out of the use of any information contained within. A line popped out after installing a radiator? Tightening torque: 4 Nm — Remove hex socket bolt -1-, retaining nut -2-. Figure 4 Slide the air diverter for the intercooler away from the front of the car red arrow and use a T20 Torx and first remove the single screw holding the line in front of the condenser in place yellow arrow and then use a T30 Torx and remove the single screw holding the line in the front green arrow. The various electrical circuits are protected by fuses. If there is a bulge in the hose, or any type of crack in the surface of the hose, then you should replace it as well.
All the information in this article is in accordance with the Service Schedule Intervals Plan specified by Audi. Check if the fastener is missing. Figure 8 Drain the coolant from the radiator. This is a common problem and the leading cause of radiator replacement; again use caution and care when working on the radiator and connections. Audi b6 a4 18t coolant flange replacement ecs tuning here's a right angle view of the same coolant flange showing the two mounting holes for the head studs note the elbowshaped hose to the right. If it feels very hard, then it might be time to replace it. Begin by draining the coolant.
It helps if you can pinch off the line first, but even then a little fluid will escape. Install mounting hooks and pins on the engine sling and secure them with the positioning lock. Chemical and lubricants, and more. It is much easier to drain the fluid from the coolant temperature sensor green arrow. The plastic connections on both the radiator and connections are a known weak point and can break surprisingly easily; use care and take your time when separating. Use care so as not to break the connection.
The overflow hose is a hose clamp and can be removed with pliers. Vehicles with automatic transmission: — Remove right charge air cooler by disconnecting upper hose connection; charge air cooler supported in 3x rubber bearings. Please see our article on temperature sensor replacement for additional assistance. The drain valve is in a very difficult area to reach and it is much easier to slide the clip holding the temperature sensor in the hose connection off and pull the sensor out. Pelican Parts is not associated with Porsche Cars North America in any manner, except for a mutual appreciation and love of the cars.
You will be removing both of the transmission lines from the radiator and some fluid is going to spill out; make sure to place a catch tray under the front of the vehicle. Move the line out of the way. Tightening torque: 16 Nm — Unbolt cable at terminal D+ -2-. Tightening torque: 65 Nm — Remove starter forward and out. Follow the steps in this video to see how to fix minor coolant antifreeze leaks in your 2002 Audi A4 Quattro. Before you start, disconnect the ground terminal from the battery and make sure it cannot accidentally make contact with it while working. Fuel system is under pressure! It must still be in production or has not been created yet.
It is highly recommended that when prompted to enter it, you do so. It should spring back to its original shape pretty quickly after being compressed. Remove the old battery, making note of their orientation, and replace with new one. Reattach the footrest or the cover. There is also a sticker listing the fuses in each of the fuse boxes in the dash panel. These can get stuck on and need a fair amount of force to remove. If that happens, Launch Control will be unavailable for a few minutes.
Be aware that the transmission temperature may increase considerably after using the Launch Control Program. The fuse boxes are located behind covers on the left and right sides of the dash panel and in the compartment on the right side of the boot. High mileage is not necessarily an indication that an overhaul is needed, while low mileage doesn? The outlet pipe should be cold the tubing that leads back to the compressor. Step 4: Re-install battery, and after it the key blade. Move the gear selector lever to the S position. When you gently squeeze a hose, it should be relatively soft and easy to indent with your hand.
Just make sure you do not break the radiator while doing it. The link will take you to a page where you can select your year and engine. Just make sure you do not break the radiator while doing it. Battery orientation is with the + side down. Simply set your year, make, model, and engine, and then select a category.