In certain instances, these items may not operate at all. Follow the Adding Keys procedure in the appropriate Service Information only when adding an additional transmitters to the vehicle. If you are trying to program method of holding down unlock switch on the truck and cycling the ignition on off on off do you hear it cycle the door locks to confirm it has entered program mode? Sometimes, parasitic drain exceeds what is normal, and can cause car battery drain. Correction Important: For clarification purposes, the following information is provided. They might be bad ones that they pawned off on you. I'm not certain this is a reset switch, but I'm thinking it is.
Iv followed the steps to a T. My dealer doesn't seem to understand this stuff. Glad to hear that you finaly got it working properly. Refer to published Service Information for the symptom experienced by the customer. I have filed a complaint, so we will see what happens. Follow the Replacing Keys procedure in the appropriate Service Information any time a transmitter is required to be unlearned or erased from a vehicle. If the software is not 23.
Well, I must say, that's a much more thoughtful answer than the first. Sent from my iPhone using. Here is a listing that is cheaper then what you paid. Not even sure which fuse runs it. I had a co-worker try them on his 2006.
Receiver is self clipped on driver side and easily replaced. The module is at the bottom left of the panel, and has a blue plug. This is bugging me My best friend has the same car but his has it and I cant figure out how to get it on mine. If a 1995 back had it it would be accessable from the trunk by pulling the carpet that is behind the back seat. Perform the following procedure step by step do not skip a step to determine the proper course of action. I've read your same response word for word posted by other people on other forums.
Iv checked the fob at vatozone and works on their rf detector. Avoiding these warning signs or delaying taking action could cause further vehicle damage, or even a system-wide failure. I did have to take the car into the dealership to have the part programed to the vehicle. The Constant clicking could be because you tried to use the remote transimtter thus activating the module before you found the battery was drained. I have a 2006 silverado, I even double checked the part number, and the fcc.
Then you would not have got this reply. Below, I requested that you try your remote with and without the antenna. If a new transmitter is being learned to a vehicle to replace a damaged, inoperative, missing, or stolen transmitter, the Replacing Keys procedure must be used to ensure that the old transmitter cannot be used to access or start the vehicle after programming. Roger I believe it is. I have a 2014 with no key fobs, but with On-Star, Cargo, Duramax if it makes a difference. There is a resync and programming method.
Six clips + or - holding this panel down with a foam rubber strip across the front next to the windshield pressure sealed. Any assistance is appreciated before I bring it to the dealers for help. I never did it because I was afraid of looping my cars computer. It also coordinates the operating functions of many non-engine related ancillary items as well as security features. To resync a fob all you would have to do is stand close to vehicle and press and hold simultaneously the lock and unlock buttons for approx 7 seconds.
I have a 2014 with no key fobs, but with On-Star, Cargo, Duramax if it makes a difference. I think this is for two but I would contact the seller first to make sure it is for two. The transmitter does not send the same signal twice to the receiver. Return the vehicle to the customer. My question is, are these particular modules known to fail, or is it more likely that a bad actuator is sending a faulty signal to it causing it to cycle? I found this somewhere not sure if it could be my problem. Wrong It did haveto go to the dealership for programming. I manually opened the drivers door and could hear a clicking noise under the dash.
A total of eight transmitters can be learned to a vehicle. Just to replace my module with this new one and hopefully it will work! The door locks should cycle to confirm synchronization. I wish that it was gas door. It streamlines the manufacturing and troubleshooting aspects of electronic modules by housing the modules into one, central unit instead of each function having its own device. Why would you think the module was faulty and the battery drain was from the module. The Constant clicking could be because you tried to use the remote transimtter thus activating the module before you found the battery was drained. I was able to disconnect the unit, my door locks still work with the door buttons.
Good luck with your repair! Problem: My remote Transmitter wouldn't program with the truck. . In order to synchronize the transmitter with the receiver, perform the following: Stand close to the vehicle. Can you add a remote? It didn't come with keyless entry remotes, can I just buy a set off of Ebay and program myself? Please discard Corporate Bulletin Number 03-08-52-001B Section 08 -- Body and Accessories. This page gives you a few part numbers for your truck. I never did it because I was afraid of looping my cars computer.